Apollo Whole Home Care Plan: Heating, Cooling, Plumbing, and Electrical Systems Plus Appliance Repairs

Whole Home Care Plan Agreement – Platinum Level ($59.95/month)*

In addition to maintenance and repairs for upto 2 heating and cooling systems, the Whole Home Agreement also covers your built-in appliances, plumbing and electrical systems – all for as little as $59.95 per month.  If you want maximum peace of mind, the Whole Home Agreement is for you.

– 100% coverage parts and labor for all cooling, heating, plumbing, electrical, and appliance repairs up to a $1,000 limit per occurrence**

– You can apply the cost of the repair (up to $1,000 limit)  towards a new piece of equipment if you decide it is smarter to replace the equipment rather than repair it.

Cost of plan is $59.95 a month*

Repairs including :

  • Heat Exchanger
  • Evaporator Coil
  • Condensing Coil
  • Compressor
  • Thermostat
  • Refrigerant
  • Thermocouple
  • Belts, Valves, Controls
  • Blower Motors
  • Fans
  • Circuit Boards
  • Blower Wheel
  • Fan Motors
  • Gas, Regulator and Pilot
  • Ignition Controls and Sensors
  • Transformers, Capacitors, Relays
  • Cycle Timer
  • Boiler Controls
  • Safety and Overload Controls

*base level coverage
** 100% coverage parts and labor applies only for repairs on issues not existing prior to the beginning date of coverage.  Appliance repairs are covered up to a maximum of $2000 annually.

Click to Download or View Apollo Home Care Plans Terms Conditions

15-Point Master Heating Tune-Up

  1. Test and adjust safety and operating controls
  2. Test gas valve or oil pump operation
  3. Inspect for combustion leaks
  4. Test and tighten all wiring and connections
  5. Conduct carbon monoxide testing
  6. Adjust and clean thermostat
  7. Inspect heat exchanger and clean burner(s)
  8. Adjust burner(s) for maximum efficiency
  9. Inspect flue pipe and draft diverter or barometric damper
  10. Adjust and clean electrode or pilot assembly
  11. Check blower motor (and belt if applicable)
  12. Drain expansion tank or install customer supplied air filter
  13. Replace oil filter and nozzle or test and adjust pressure regulator
  14. Lubricate all motors, bearings, fans and circulators
  15. Inform customer of equipment condition and provide printed report.

 

15-Point Master Cooling Tune-Up

  1. Lubricate all moving parts
  2. Safety test all controls for proper operation
  3. Install gauges; record operating pressures and temperatures
  4. Inspect start and run capacitors and relays for bulges, rust and leaks
  5. Measure refrigerant superheat to fine-tune its charge
  6. Flush condensate drain to protect against overflow
  7. Tighten and safety test all wiring and connections
  8. Check blower motor (and belt if applicable)
  9. Test “temperature drop” at return and supply air; adjust blower
  10. Adjust and clean thermostat
  11. Meter voltage and amperage in all motors; test for worn bearings
  12. Test condition of compressor contacts
  13. Check air filter; clean or replace with customer supplied filter
  14. Clean outdoor condenser coil
  15. Inform customer of equipment condition and provide printed report

 

15-Point Master Plumbing Tune-Up

  1. Locate, label and check main water shut off valve
  2. Check water pressure
  3. Check expansion tank
  4. Check washer hose connections
  5. Check sump pump (if applicable)
  6. Visual evaluation of all exposed plumbing
  7. Water hardness test
  8. Check for slow drains
  9. Check shower heads
  10. Dye test water closet
  11. Check shut off valves
  12. Check of shoer/tub caulking
  13. check outside faucets
  14. Check disposal for wear
  15. Written report of all recommendations

 



How to Videos

    How much insulation needed for an attic